Projector Setup Settings - Extended Menu

Settings on the Extended menu let you customize various projector setup features that control its operation.

Setting Options Description
Display See the next table in this topic
Closed Caption Off



Controls use of closed captions and selects the closed caption type (closed captions are only visible for NTSC signals connected through the S-Video or Video ports)
User's Logo Creates a screen that the projector displays to identify itself and enhance security
Projection Front



Rear Ceiling

Selects the way the projector faces the screen so the image is oriented correctly
Direction Varying levels available Selects the installation angle for the projector; the projector's fan may get louder depending on the direction angle selected
Operation See the last table in the topic
A/V Settings A/V Output

Monitor Out

Audio Settings

Selects various audio and video output settings

A/V Output: select to output audio and video to an external device when the projector is in standby mode (Standby Mode must be turned on to use this setting)

Monitor Out: Select the image source to output to an external device when the projector is in standby mode. When set to Auto, an analog RGB signal from the Computer or BNC ports is output depending on which source was selected when the projector went into standby mode.

Audio Settings: Selects audio source to output

Standby Mode Communication On

Communication Off

Enable this setting to allow the following operations to occur when the projector is in standby mode:
  • Monitor and control the projector over a network
  • Output audio and video to an external device (A/V Output must be set to Always On)
  • Communication from the HDBaseT port (PowerLite Pro G6750WU/G6800/G6900WU)

(PowerLite Pro G6750WU/G6800/G6900WU)

Control Communications When the projector is connected to the HDBaseT Transmitter, enables or disables communication from the Ethernet and serial ports on the transmitter; turning on this setting disables the projector's LAN, RS-232C, and Remote ports
Multi-Projection Brightness Level

(PowerLite Pro G6050W/G6150/G6550WU/G6750WU/G6800/G6900WU)

Edge Blending


Projector ID

Select various options when projecting from multiple projectors

Brightness Level: adjusts the brightness of the lamp; Power Consumption in the Settings menu must be set to Normal to use this setting

Edge Blending: blends the border between multiple images to create a seamless screen

Multi-screen: adjusts the tint and brightness of each projected image

Projector ID: sets the projector to a particular ID number which allows you to use a remote control to individually control projectors

Schedule Settings Schedule specific operations to occur at a pre-scheduled time.
Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option)

Display settings

Setting Options Description
Menu Position Selects the position of the projector menu displayed on the screen
Messages Controls whether messages are displayed on the screen
Display Background Selects the screen color or logo to display when no signal is received
Startup Screen Controls whether a special screen appears when the projector starts up
A/V Mute Selects the screen color or logo to display when A/V Mute is turned on
Standby Confirmation Displays a confirmation message after pressing the Standby button on the remote control
Air Filter Notice Displays a message when a clog in the air filter is detected
Screen Sets the aspect ratio and position of the projected image according to the type of screen being used
Panel Alignment Corrects color misalignment in the projected image
Color Uniformity Adjusts the color tone balance

Operation settings

Setting Options Description
Direct Power On Turns on the projector when you plug it in
Sleep Mode Automatically turns off the projector after an interval of inactivity
Sleep Mode Timer Sets the time before the projector automatically turns off (Sleep Mode must be turned on)
High Altitude Mode Regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m)
BNC Sync Termination Sets the termination for the signal from the BNC port (normally should be off unless analog termination such as for switchers is necessary)
Remote Control Type Normal


Select Normal to use the remote control that came with the projector or Simple to use a different Epson projector remote control (selecting Simple disables the remote control that came with the projector)
Inv Direction Button Enable this setting if the projector is installed on a ceiling and you want to invert the arrow buttons on the control panel
Startup Source Search Automatically detect the image signal being input when the projector is turned on
A/V Mute Release A/V Mute


Select A/V Mute if you want to use only the A/V Mute button to turn off A/V mute or select All to use any button to turn it off
Beep Turns on or off the beep that is played when the projector turns on or off
Lens Type ELPLU01


Select ELPLU01 when the optional short throw lens (ELPLU01) is attached; otherwise leave this setting at Others
Date & Time Adjusts the projector's system time and date settings