Follow these safety instructions when setting up and
using the projector:
- Do not
look into the lens when the projector is on. The bright light can
damage your eyes. Avoid standing in front of the projector so the
bright light does not shine into your eyes.
- Do not
place the projector on an unstable cart, stand, or table.
- Do not
operate the projector on its side, or while tilted to one side.
Do not tilt the projector more than 30° forward or back.
- If the
projector is mounted on a ceiling or wall, it should be installed
by qualified technicians using mounting hardware designed for use
with this projector.
- When
installing or adjusting a ceiling or wall mount, do not use
adhesives to prevent the screws from loosening and do not use oils
or lubricants. This may cause the projector case to crack and the
projector to fall from its ceiling mount. This could cause serious
injury to anyone under the mount and could damage the
projector.
- Do not use
the projector near water, sources of heat, high-voltage electrical
wires, or sources of magnetic fields.
- Use the
type of power source indicated on the projector. Use of a different
power source may result in fire or electric shock. If you are not
sure of the power available, consult your dealer or power
company.
- Place the
projector near a wall outlet where the plug can be easily
unplugged.
- Take the
following precautions when handling the plug: Do not hold the plug
with wet hands. Do not insert the plug into a dusty outlet. Insert
the plug firmly into the outlet. Do not pull the power cord when
disconnecting the plug; always be sure to hold the plug when
disconnecting it. Do not overload wall outlets, extension cords, or
power strips. Failure to comply with these precautions could result
in fire or electric shock.
- Do not
place the projector where the cord can be walked on. This may
result in fraying or damage to the plug.
- Unplug the
projector from the wall outlet and allow to cool before cleaning.
Use a dry cloth (or, for stubborn dirt or stains, a moist cloth
that has been wrung dry) for cleaning. Do not use liquid or aerosol
cleaners, any sprays containing flammable gas, or solvents such as
alcohol, paint thinner, or benzine.
- Do not
block the slots and openings in the projector case. They provide
ventilation and prevent the projector from overheating. Do not
operate the projector on a sofa, rug, or other soft surface, or set
it on top of loose papers. Do not cover the projector with a
blanket, curtain, or tablecloth. If you are setting up the
projector near a wall, leave at least 7.9 inches (20 cm) of space
between the wall and the projector.
- Do not
operate the projector in a closed-in cabinet unless proper
ventilation is provided.
- Never
allow objects of any kind to enter any openings in the projector.
Do not leave objects, especially flammable objects, near the
projector. Never spill liquid of any kind into the projector.
- If you are
using two or more projectors side-by-side, leave at least
2 feet (60 cm) of space between the
projectors to allow for proper ventilation.
- You may
need to clean the air filter and vent. A clogged air filter or vent
can block ventilation needed to cool the projector. Do not use
canned air, or the gases may leave a residue.
- Do not
store the projector outdoors for an extended length of time.
- Except as
specifically explained in this manual, do not attempt to service
this product yourself. Refer all servicing to qualified personnel.
Opening or removing covers may expose you to dangerous voltages and
other hazards.
- Never open
any covers on the projector except as specifically explained in
this manual. Never attempt to disassemble or modify the projector.
Refer all repairs to qualified service personnel.
- Unplug the
projector from the wall outlet and refer servicing to qualified
service personnel under the following conditions: if it does not
operate normally when you follow the operating instructions, or
exhibits a distinct change in performance; if smoke, strange odors,
or strange noises come from the projector; if the power cord or
plug is damaged or frayed; if liquid or foreign objects get inside
the projector, or if it has been exposed to rain or water; if it
has been dropped or the housing has been damaged.
- Do not
touch the plug during an electrical storm. Otherwise, you may
receive an electric shock.
- Unplug the
projector when it will not be used for extended periods.
- Do not use
the projector where it may be exposed to rain, water, or excessive
humidity.
- Do not use
or store the projector where it may be exposed to smoke, steam,
corrosive gases, excessive dust, vibration, or shock.
- Do not use
the projector where flammable or explosive gases may be
present.
- Do not use
or store the projector or remote control in a hot location, such as
near a heater, in direct sunlight, or in a closed vehicle.
- If you use
the projector in a country other than where you purchased it, use
the correct power cord for that country.
- Do not
stand on the projector or place heavy objects on it.
- Do not use
the projector outside of the required temperature range below:
41 to 95 °F (5 to 35 °C) at an altitude of 7500 feet
(2286 m) or less, or 41 to 86 °F (5 to 30 °C) at a higher
altitude
Doing so may cause an unstable display and could lead
to projector damage. Do not use or store the projector where it may
be exposed to sudden changes in temperature.
- Do not
store the projector outside of the required temperature range of 14
to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of
time. Doing so may cause damage to the case.
- Do not
place anything that can become warped or damaged by heat near the
exhaust vents. Do not bring your hands or face close to the vents
while projection is in progress. Do not bring your face close to
the projector while it is in use.
- Before you
move the projector, make sure its power is turned off, the plug is
disconnected from the outlet, and all cables are disconnected.
- Never try
to remove the lamp immediately after use because it will be
extremely hot. Before removing the lamp, turn off the power and
wait at least an hour to allow the lamp to cool completely.
- Do not
place the source of an open flame, such as a lit candle, on or near
the projector.
- Do not
block the lens during projection using a book or any other object.
This could damage the projector or cause a fire.
- Do not
modify the power cord. Do not place heavy objects on top of the
power cord or bend, twist, or pull it excessively. Keep the power
cord away from hot electrical appliances.
- Always
attach the lens unit cap to the lens when not using the projector
to prevent the lens from becoming dirty or damaged.
Note:
The lamp(s)
in this product contain mercury. Please consult your state and
local regulations regarding disposal or recycling. Do not put in
the trash.
WARNING: The cords
included with this product contain chemicals, including lead, known
to the State of California to cause birth defects or other
reproductive harm. Wash
hands after handling. (This notice is provided in
accordance with Proposition 65 in Cal. Health & Safety Code §
25249.5 and following.)