Setting | Options | Description |
---|---|---|
Paper Source Settings | Various options | See the Paper Source Settings table below |
Custom Paper Setting | 1 to 10 | See the Custom Paper Setting table below |
Printing Language* | USB
Network |
Select the printing language to use for each
connection mode
Auto: select for most printing situations HP-GL/2: select if HP-GL/2 or HP RTL print data sent from a CAD application does not automatically switch the printing mode |
Universal Print Settings* | Various options | See the Universal Print Settings table below |
HP-GL/2 Unique Settings | Various options | See the HP-GL/2 Unique Settings table below |
Thick Paper | Off
On |
Select On to widen the platen gap to prevent scuffing if you are printing on thick paper |
Bidrectional | On
Off |
Select On if you
want the print head to move left and right during printing
Select Off to decrease misalignment of ruled lines, but slow down printing |
PC Connection via USB | Enable
Disable |
Select Enable to allow access to the printer from a USB-connected computer |
USB I/F Timeout Setting | 0 seconds, 5 to 300 seconds | Specifies the length of time before ending communication from a USB-connected computer |
* The Printing Language and Universal Print Settings menus can be locked by an administrator. If you cannot access or change these settings, contact your administrator for assistance.
Paper Source Settings
Setting | Options | Description |
---|---|---|
Error Notice | Paper Size
Notice
Paper Type Notice |
Select On to display an error message when the output size or paper type settings are different between the driver and printer |
Roll Paper Setup | Detect Paper Meandering | Select On to display an error message and stop printing if the printer detects the paper is skewed |
Print Cutting Guideline | Select On to print cut lines on roll paper (if Auto Cut is turned off) | |
After-Print Options | Hold Paper | Select to hold paper in the paper eject slot after printing; manually grasp the edge of the paper and remove it from the printer to prevent it falling on the floor |
Eject Paper | Select to fully eject cut sheets or automatically cut roll paper after printing |
Custom Paper Setting
Universal Print Settings
Setting | Options | Description |
---|---|---|
Paper Source | Roll Paper
Auto Sheet Feeder Cut Sheet (1 sheet) |
Select the paper source from which you want to print |
Quality | Standard
Speed Fine Super Fine |
Select the print quality |
Color Mode | Color
Black/White |
Select the color you want for printing |
Page Margins option | Clip By Margins | Adds the value selected for the page margin inside the hard clip area of the PS command of the data, or the size selected for the base output size |
Oversize | Adds the value selected for the page margin
outside the hard clip area of the PS command of the data (when Auto
is selected)
Adds the value selected for the page margin outside the size selected for the base output size (when set to a standard size) |
|
Page Margin | 3 mm
5 mm |
Select the top, bottom, left, and right margin
values for roll paper
Margins are 3 mm for cut sheets regardless of the setting. |
Smoothing | On
Off |
Select On to print at the maximum resolution for the selected paper type. This may result in longer printing time or insufficient memory errors. |
Base Output Size | Various options | When Auto (the
default setting) is selected, the hard clip area of the PS command
of the data becomes the base output size
Select User-Defined when printing in a custom size |
Resolution | Standard
300 dpi 600 dpi 1200 dpi |
Selects the print resolution; when Standard (the default setting) is selected, available resolutions depend on the selected paper type |
Color Mode (Common) | EPSON Standard (sRGB) | Optimize the sRGB space and correct the color |
Business Graphics | Perform color correction to optimize your images based on the sRGB space | |
GIS | Perform color correction when printing topographical maps | |
Line Drawing | Perform color correction when printing CAD drawings and other line drawings | |
Off (No Color Management) | No color correction is performed |
HP-GL/2 Unique Settings
Adjust these settings as necessary when printing in HP-GL/2 or HP RTL mode.
Setting | Options | Description |
---|---|---|
Rotate | 0°
90° 180° 270° |
Rotate the coordinates of the drawn data counterclockwise before printing |
Origin Setup | Left Edge
Center |
Set the data coordinate origin |
Mirror Image | On | Select to horizontally flip the image using the center of the output size width as the basis line |
Off | Select to print without flipping the image | |
Line Merge | On | Select to merge the intersection of overlapping lines within the image according to the MC command of the data |
Off | Select to move lines to be printed later to the front at intersections | |
Color Mode (HP-GL/2) | EPSON Standard (sRGB) | Optimize the sRGB space and correct the color |
Business Graphics | Perform color correction to optimize your images based on the sRGB space | |
GIS | Perform color correction when printing topographical maps | |
Line Drawing | Perform color correction when printing CAD drawings and other line drawings | |
Off (No Color Management) | No color correction is performed | |
Select Palette | Software | Print according to the pen configurations set in the application and ignore the built-in printer palette |
Default | Print according to the built-in printer palette settings (logical pen with a pen width of 0.35 mm and 256 colors) | |
Palette A
Palette B |
Print according to the built-in printer palette settings specified under Define Palette | |
Define Palette | Palette A
Palette B |
Define a built-in palette by specifying the pen width and color for the 16 types of logical pens |
Restore Default HP-GL/2 Unique Settings | No
Yes |
Select Yes to restore all HP-GL/2 Unique Settings to their defaults |