| Blue |
Blue |
Varies |
Off |
Normal operation |
| Blue |
Flashing blue |
Varies |
Off |
Warming up; wait for an image to appear (30 seconds);
all buttons are disabled during warmup |
| Blue |
Flashing blue |
Off |
Off |
Cooling down; all buttons are disabled |
| Blue |
Off |
Off |
Off |
Standby or network monitoring and control mode (when
Standby Mode is set to
Communication On) |
| Flashing blue |
Off |
Off |
Off |
Preparing for network monitoring, quick startup, or
USB Power mode; all buttons are
disabled |
| Blue |
Blue |
Flashing blue |
Off |
Shutter is closed |
| Varies |
Flashing blue |
Flashing orange |
Varies |
Refresh Mode is
on |
| Flashing blue |
Varies |
Varies |
Flashing orange |
Projector is too hot
- Make sure
that the vents are not clogged with dust or obstructed by nearby
objects
- Make sure the environmental temperature is not too
hot
|
| Off |
Flashing blue |
Off |
Orange |
Projector has overheated and turned off; leave the
projector off for at least 5 minutes
- Make sure
that the vents are not clogged with dust or obstructed by nearby
objects
- Make sure
the environmental temperature is not too hot
- If
operating the projector at high altitude, turn on High Altitude Mode
- If the
problem persists, unplug the projector and contact Epson for
help
|
| Flashing blue |
Varies |
Flashing orange |
Varies |
Laser error; turn off the projector, unplug it, and
contact Epson for help
An unsupported lens is attached; remove the
unsupported lens and attach a lens that is supported |
| Off |
Flashing blue |
Orange |
Orange |
Lens Shift or Supply Voltage error; turn off the
projector, unplug it from the electrical outlet, and contact Epson
for help
No lens is installed; attach or re-install lens; if
the problem persists, unplug it from the electrical outlet, and
contact Epson for help. |
| Flashing blue |
Varies |
Flashing orange |
Flashing orange |
Shutter warning; turn off the projector, unplug it,
and contact Epson for help |
| Off |
Flashing blue |
Orange |
Off |
Laser or retardation plate error; turn off the
projector, unplug it, and contact Epson for help
Upper case open error; turn off the projector, unplug
it, and contact Epson for help |
| Off |
Flashing blue |
Off |
Flashing orange |
Cooling system error; turn the projector off, unplug
it, and contact Epson for help
A fan or sensor has a problem; turn the projector off,
unplug it, and contact Epson for help |
| Off |
Flashing blue |
Flashing orange |
Off |
Internal error; turn off the projector, unplug it
from the electrical outlet, and contact Epson for help |
| Off |
Flashing blue |
Orange |
Orange |
Lens problem or no lens is installed; Lens Shift
error; Supply Voltage error; Communication error with AC Micro
controller
- Remove and reattach the installed lens
- Attach a supported lens
- If the problem persists, unplug the projector and
contact Epson for help
|
| Varies |
Varies |
Flashing orange |
Varies |
The projector is unable to maintain constant
brightness and the Constant
Brightness setting in the Settings menu is disabled |
| Off |
Flashing blue |
Flashing orange |
Flashing orange |
Shutter error; turn off the projector, unplug it, and
contact Epson for help |
| — |
— |
Flashing orange quickly |
Flashing orange quickly |
The batch setup file may be corrupt, or the USB flash
drive may not be connected correctly.
Disconnect the USB flash drive, unplug and then plug
in the projector's power cord, and then try again. |
| Flashing blue quickly |
Flashing blue quickly |
Flashing orange quickly |
Flashing orange quickly |
Writing the settings may have failed and an error may
have occurred in the projector's firmware; turn off the projector,
unplug it, and contact Epson for help |
