Be sure to
follow all warnings and instructions marked on the product.
Except as
specifically explained in your documentation, do not attempt to
service the product yourself.
Do not install or store the product in an unstable location or
a location subject to vibrations from other equipment. The product
could fall or tip over and cause an injury.
Do not install the product in locations subject to oily smoke
and dust, or in locations subject to humidity or where it could
easily get wet. An electric shock or fire could occur.
Keep children away from this product, otherwise injury may
occur.
Place the
product on a flat, stable surface that extends beyond its base in
all directions. It will not operate properly if it is tilted or at
an angle.
Leave enough
room around the product for sufficient ventilation. Do not block or
cover openings in the cabinet or insert objects through the
slots.
Do not tilt the product more than 10 degrees in any direction
while moving it. Doing so may cause the product to fall and cause
damage or personal injury.
Avoid
locations that are subject to rapid changes in heat or humidity,
shocks or vibrations, or dust.
To ensure the colors you want to print, maintain a constant
room temperature of 59 to 77 ?F (15 to 25 ?C).
Do not place
or store the product outdoors.
Do not place
the product near excessive heat sources or in direct sunlight.
Do not cover the product with a cloth or install it in a
location with poor ventilation.
Do not attempt to move the product alone; three people are
required to move the product.
When lifting the product, make sure you lift with your hands at
the correct locations; otherwise, the product may fall or you may
be injured. See the link below or the Start Here sheet for
details on lifting the product.
Use correct posture when lifting the product.
Make sure to remove all packing materials from the product and
installation area.
When placing the product on a stand with casters, make sure the
casters are secured before you perform any work so that they do not
move. If the stand moves while you are performing any work, it
could cause an injury.
Do not use the product in locations with volatile substances
such as alcohol or thinner, or near naked flames. An electric shock
or fire could occur.
Do not use the product if it is giving off smoke or if you
notice any abnormal odors or noises. An electric shock or fire
could occur. If any abnormalities occur, turn off the power and
unplug the power cable immediately, then contact your dealer or
Epson Support.
Do not spill
liquid on the product or use the product with wet hands.
Do not insert or unplug the plug with wet hands.
Do not use
aerosol products that contain flammable gases inside or around the
product. Doing so may cause fire.
Keep the
product away from potential sources of electromagnetic
interference, such as loudspeakers or the base units of cordless
telephones.
When
connecting the product to a computer or other device with a cable,
ensure the correct orientation of the connectors. Each connector
has only one correct orientation. Inserting a connector in the
wrong orientation may damage both devices connected by the
cable.
Use only the
type of power source indicated on the product's label.
Use only the
power cord that comes with the product. Use of another cord may
cause fires or shock. Do not use the cord with any other equipment.
Do not modify the cord.
Place the
product near a wall outlet where the plug can be easily
unplugged.
Make sure the plug is fully inserted into the outlet.
Connect your
product to a properly grounded power outlet. Avoid plugging the
product into an outlet on the same circuit as a photo copier or air
control system that regularly switches on and off, or on an outlet
controlled by a wall switch or timer.
Do not route the power cord near heaters or other heat
sources.
Be sure your power cable meets relevant safety standards of the
area where you plan to use it.
Do not connect the power cable to a power strip or a
multi-outlet extension cord; otherwise an electric shock or fire
could occur. Supply power directly from a household power outlet
(100 V AC).
Do not let
the power cable become damaged or frayed. Place it to avoid
abrasions, cuts, fraying, crimping, and kinking. Do not place
objects on top of it and do not allow it to be stepped on or run
over. Be careful to keep the cord straight at each end.
Do not modify the power cable. Do not place anything heavy on
the power cable. Do not bend, twist, or pull forcefully on the
power cable.
If you use
an extension cord with the product, make sure the total ampere
rating of the devices plugged into the extension cord does not
exceed the cord's ampere rating. Also, make sure the total ampere
rating of all devices plugged into the wall outlet does not exceed
the wall outlet's ampere rating.
If damage
occurs to the plug, replace the cord set or consult a qualified
electrician. If there are fuses in the plug, make sure you replace
them with fuses of the correct size and rating.
Unplug the
product and refer servicing to qualified service personnel under
the following conditions: if the power cord or plug is damaged; if
liquid has entered the product; if the product has been dropped or
the cabinet damaged; if the product does not operate normally or
exhibits a distinct change in performance. Adjust only those
controls that are covered by the operating instructions.
Only route the cables as indicated in the Start Here
sheet. When connecting cables or optional accessories, make sure
they are installed in the correct direction and that you follow the
procedures exactly.
If any foreign objects or liquids enter the printer, stop using
it immediately. An electric shock or fire could occur. Turn off the
power and unplug the power cable immediately and then contact your
dealer or Epson Support.
Always turn
off the product using the power button, and wait until the power
light stops flashing before unplugging the product or cutting off
power to the electrical outlet.
If you will
not be using the product for a long period, unplug the power cord
from the electrical outlet.
When unplugging the plug, grip the plug itself; do not pull the
power cord.
Unplug the plug regularly and clean between the blades and
around the base of the blades. If the plug is plugged in for an
extended period of time, dust collects around the base of the
blades and a short circuit or fire could occur.
Do not use the plug if dust or any other foreign objects have
adhered to the plug; otherwise an electric shock or fire could
occur.
Do not put your hands inside the product and be careful not to
trap your hands or fingers when opening or closing the product
cover.
Do not touch the flat white cable or any areas marked with a do
not touch label.
Do not disassemble anything except as indicated in the
product's documentation.
Do not touch any areas inside the product except for those
indicated in the product's documentation; otherwise, you may be
shocked or burned.
Do not sit on the product or place heavy objects on top of
it.
Do not insert or drop metallic or flammable items into the
openings on the product.
Before storing the product, make sure the print head is
positioned at the far right.
When storing
or transporting the product, do not tilt it, stand it on its side,
or turn it upside down; otherwise ink may leak.
Note: The lithium
batteries in this product contain Perchlorate Material - special
handling may apply. Click here for details.