Projector Setup Settings - Extended Menu

Settings on the Extended menu let you customize various projector setup features that control its operation.



Setting Options Description
Display See the Display settings table in this topic
User's Logo Creates a screen that the projector displays to identify itself and enhance security
Projection Front

Front/Ceiling

Rear

Rear Ceiling

Selects the way the projector faces the screen so the image is oriented correctly
Operation See the Operation settings table in this topic
A/V Settings A/V Output Select Always On to set a fixed IP address and move the lens to the home position when the projector is in standby mode (the Standby Mode setting must be set to Communication On)
Standby Mode Communication On

Communication Off

Enable this setting to allow the following operations to occur when the projector is in standby mode:
  • Monitor and control the projector over a network
  • Output video to an external device (A/V Output must be set to Always On)
  • Communication from the HDBaseT port (Control Communications must be set to On in the HDBaseT settings)
HDBaseT Control Communications

Extron XTP

Selects the communication settings for connections to an HDBaseT transmitter or switcher

Control Communications: enables or disables communication from the Ethernet and serial ports on the transmitter; turning on this setting disables the projector's LAN, RS-232C, and Remote ports (Extron XTP must be turned off to use this setting)

Extron XTP: set to On when you connect an Extron XTP transmitter or switcher to the HDBaseT port

SDI Settings Link Type

Manual Settings

Select the signal settings for the SDI port installed in slot 1 or 2

Link Type: select Single (Auto) or Single (Manual) to configure one screen with one input signal; select Quad (Auto) or Quad (Manual) to configure one screen with four input signals or to enable the SDI1 through SDI4 ports in the Video Terminal Settings

Manual Settings: set various SDI settings manually or reset them to their default values

DisplayPort Settings Link Type Select the signal settings for an optional DisplayPort interface board installed in slot 1 or 2

Link Type: select Single when connecting one input source to either the DisplayPort 1 or 2 ports; when connecting two input sources to the ports, select Dual (3840x2160) so the computer recognizes the signal as one display (if an image is not displayed, select Dual (1920x2160) so the computer recognizes the signal as two displays)

Color Calibration Start Auto Adjustment

Undo

Redo

Color Uniformity

Automatically detects color deterioration and adjusts the color tone

Start Auto Adjustment: automatically adjusts the color tone for the whole image

Undo and Redo: undoes or redoes the auto adjustment

Color Uniformity: adjusts the color tone balance for the whole image

Multi-Projection Projector ID

Projector Grouping

Tiling

Geometry Correction

Edge Blending

Black Level

Scale

Screen Matching

Select various options when projecting from multiple projectors

Projector ID: sets the projector to a particular ID number which allows you to use a remote control to individually control projectors

Projector Grouping: lets you select the projectors being used to project one image

Tiling: sets the number of split screens and the position of each image

Geometry Correction: corrects image distortion

Edge Blending: blends the border between multiple images to create a seamless screen

Black Level: adjusts the brightness and tone differences in overlapping images

Scale: adjusts the scale of the images

Screen Matching: adjusts the tint and brightness of the images

Schedule Settings Various scheduling options Lets you schedule various projector tasks
Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option)
Note: You cannot set the Scale setting when the Link Type for the DisplayPort Settings is set to one of the Dual options.

Display settings

Setting Description
Menu Position Selects the position of the projector menu displayed on the screen
Message Position Selects the position of messages displayed on the screen
Messages Controls whether messages are displayed on the screen
Display Background Selects the screen color or logo to display when no signal is received
Startup Screen Controls whether a special screen appears when the projector starts up
Standby Confirmation Displays a confirmation message after pressing the Standby button on the remote control
Air Filter Notice Displays a message when a clog in the air filter is detected
Screen Sets the aspect ratio and position of the projected image according to the type of screen being used
Panel Alignment Corrects color misalignment in the projected image
Color Uniformity Adjusts the color tone balance
OSD Rotation Rotates the menu display 90°

Operation settings

Setting Description
Direct Power On Turns on the projector when you plug it in
Sleep Mode Automatically places the projector in standby mode after an interval of inactivity
Sleep Mode Timer Sets the time before the projector automatically turns off (Sleep Mode must be turned on)
High Altitude Mode Regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m)
Startup Source Search Automatically detects the image signal being input when the projector is turned on
Shutter Settings Adjusts the shutter settings

Fade-in: sets the number of seconds for a fade-in transition effect when displaying an image

Fade-out: sets the number of seconds for a fade-out transition effect when hiding an image

Shutter Timer: turns off the projector automatically after using the shutter and 2 hours of inactivity has passed

Shutter Release: select Shutter if you want to use only the Shutter button to turn off the shutter, or select Any Button to use any button to turn it off

Startup: select the shutter status for when you turn on the projector

Standby: select the shutter status for when the projector is in standby mode or select Last Used to maintain the current shutter status when you turn off the projector

Video Terminal Settings Enable or disables each video input port
Advanced See the next table in this topic
Date & Time Adjusts the projector's time and date settings
Lens Calibration Displays information about the lens currently in use and lets you start lens calibration

Advanced settings

Setting Description
Beep Controls the beep that sounds when you turn the projector on or off
Indicators Select Off to turn off projector lights, except warning lights
Log Save Destination Select where you want to save projector operation log files
Batch Setup Range Select which projector menu settings to copy using the batch setup feature; select All or select Limited to not copy the EDID settings or all Network menu settings (except the Notifications and Others menu settings)
AC Voltage Monitoring Select Off to regularly use the direct shutdown feature; if you select On for this setting and the projector is turned off by any method other than pressing the power button, a power supply voltage warning message is displayed the next time the projector is turned on
Lens Type Select the model number of the lens if you installed any of these lenses: ELPLS04, ELPLU02, ELPLR04, ELPLW04, ELPLM06,ELPLM07, or ELPLL07
Was this page helpful? Yes or No.
Privacy Policy | Your California Privacy Rights | Terms of Use