Printer Settings Menu

Select Settings > General Settings > Printer Settings to customize paper and printing options.
Setting Options Description
Paper Source Settings Various options See the Paper Source Settings table below
Custom Paper Setting 1 to 10 See the Custom Paper Setting table below
Universal Print Settings* Various options See the Universal Print Settings table below
Thick Paper Off

On

Select On to widen the platen gap to prevent scuffing if you are printing on thick paper
Bidrectional On

Off

Select On if you want the print head to move left and right during printing

Select Off to decrease misalignment of ruled lines, but slow down printing

PC Connection via USB Enable

Disable

Select Enable to allow access to the printer from a USB-connected computer
USB I/F Timeout Setting 0 seconds, 5 to 300 seconds Specifies the length of time before ending communication from a USB-connected computer

*The Universal Print Settings menu can be locked by an administrator. If you cannot access or change these settings, contact your administrator for assistance.

Paper Source Settings

Setting Options Description
Error Notice Paper Size Notice

Paper Type Notice

Select On to display an error message when the output size or paper type settings are different between the driver and printer
Roll Paper Setup Detect Paper Meandering Select On to display an error message and stop printing if the printer detects the paper is skewed
Print Cutting Guideline Select On to print cut lines on roll paper (if Auto Cut is turned off)
After-Print Options Hold Paper Select to hold paper in the paper eject slot after printing; manually grasp the edge of the paper and remove it from the printer to prevent it falling on the floor
Eject Paper Select to fully eject cut sheets or automatically cut roll paper after printing

Custom Paper Setting

Setting Options Description
Change Name Use the keyboard to enter a name for the custom paper setting (this name is displayed in the Paper Type list)
Change Reference Paper Various options Select the media type for the paper closest to the one you are using
Advanced Media Setting Platen Gap Select a larger value if print results are smudged by print head strikes
Top/Bottom Margins The Standard margins are as follows for the top and bottom:
  • CAD/line drawings: 3 mm
  • Other: 30 mm

Select a different value as necessary.

Note: Left and right margins are always 3 mm.
Back Tension Select High or Extra High if paper wrinkles during printing
Drying Time Drying Time per Pass: Select from 0 to 10 seconds for the amount of time the print head pauses to allow drying after each pass

Drying Time per Page: Select from 0 to 60 minutes for the amount of time the printer pauses to allow drying after each page is printed

Auto Cut Select On to automatically cut roll paper after each page is printed, or select Off to cut paper manually
Restore Default Restores the custom setting to the defaults

Universal Print Settings

Setting Options Description
Paper Source Roll Paper

Auto Sheet Feeder

Cut Sheet (1 sheet)

Select the paper source from which you want to print
Quality Standard

Speed

Fine

Super Fine

Select the print quality
Color Mode Color

Black/White

Select the color you want for printing
Page Margins option Clip By Margins Adds the value selected for the page margin inside the hard clip area of the PS command of the data, or the size selected for the base output size
Oversize Adds the value selected for the page margin outside the hard clip area of the PS command of the data (when Auto is selected)

Adds the value selected for the page margin outside the size selected for the base output size (when set to a standard size)

Page Margin 3 mm

5 mm

Select the top, bottom, left, and right margin values for roll paper

Margins are 3 mm for cut sheets regardless of the setting.

Smoothing On

Off

Select On to print at the maximum resolution for the selected paper type
Note: This may result in longer printing time or insufficient memory errors.
Base Output Size Various options When Auto (the default setting) is selected, the hard clip area of the PS command of the data becomes the base output size

Select User-Defined when printing in a custom size

Resolution Standard

300 dpi

600 dpi

1200 dpi

Selects the print resolution; when Standard (the default setting) is selected, available resolutions depend on the selected paper type
Color Mode (Common) EPSON Standard (sRGB) Optimize the sRGB space and correct the color
Business Graphics Perform color correction to optimize your images based on the sRGB space
GIS Perform color correction when printing topographical maps
Line Drawing Perform color correction when printing CAD drawings and other line drawings
Off (No Color Management) No color correction is performed
Related tasks
Creating Custom Paper Configurations
Selecting the Paper Settings for Each Source - Control Panel