| Prepare empty waste ink bottle. |
The waste ink bottle is almost full. Make sure
you have a replacement waste ink bottle handy. |
| Ink Supply Unit Error
Ink supply unit cannot be recognized. Re-insert or replace
it. |
Remove and reinstall the
ink pack. If the error recurs, replace the ink pack with a new one.
Condensation may have formed inside the pack. Leave the pack at
room temperature for at least four hours before installing
it. |
| Ink Supply Unit Error
Ink supply unit cannot be detected. Re-insert or replace
it. |
| Cleaning Ink Expended
Replace cleaning supply unit. |
Remove and reinstall the cleaning pack. If the
error recurs, insert a new cleaning pack.
Condensation may have formed inside the pack. Leave the cleaning
pack at room temperature for at least four hours before installing
it. |
| Ink Low |
The ink is low. Make sure you have a
replacement ink pack handy. |
| Warming Up...
Force to start printing. |
One or more heaters is warming up to the
specified temperature. To start printing without waiting for the
heater to warm up, press the OK button. |
| Command Error
Check print settings on RIP. |
Press the  pause/cancel button and
select Job Cancel. Make sure the
installed RIP software is compatible with the product. |
| Clogged nozzles detected.
Cleaning recommended. |
Perform head cleaning if necessary. |
| F/W Install Error
Firmware update failed.
Restart the printer. |
Turn off the product, wait a few minutes, and
turn it on again. Then reinstall the firmware again.
If this message persists, contact Epson for support. |
| Print head is nearing end of service life. |
The print head is nearing the end of its
service life. Contact Epson for support. |
| Auto Take-up Reel Unit stopped. |
Press the pause/cancel button and
select Job Cancel to cancel
printing. Then set the Auto switch
on the auto take-up reel to the off
position, set it back to the original position, and reattach the
media to the auto take-up reel. |
| Media Size Error
Load correct size media. |
Raise the media loading lever and remove the
currently loaded media. Be sure the media is at least
11.8 inches (300 mm) wide.
If this message appears even when the media is the correct
width, turn off the Media Size Check
setting and try printing again. |
| Media Sensor Error
Loaded media or sensor has a problem.
Refer to manual for error details. |
Press the pause/cancel button to
clear the message.
Auto Nozzle Check and
automatic media adjustment in Easy Media Setup are not available
under the following conditions:
- Loaded media
is transparent or colored
- Loaded media
has an uneven surface
- Loaded media
bleeds through easily
- Platen Gap setting is set to 2.5
- The printer
is exposed to direct sunlight or interference from other ambient
light sources
If necessary, set the Auto Nozzle
Check and Media Adjust
settings manually. |
| Media Sensor Error
Refer to manual for error details.
Adjust manually? |
| Roll Type Error
Release and then reset the media loading lever, then match Roll
Type setting to actual media. |
Make sure the Roll
Type setting matches the loaded roll type. |
Press  maintenance and perform Head
Maintenance. |
This message is displayed when regular cleaning
has not been performed for more than one month. |
| 3 layer printing is only available with 2 Head
Mode |
Set the product to use both print heads by
selecting 2 Heads Mode as the
Head Mode setting in the Printer
Setup menu. |
| Maintenance Request
Replace Part Now or Replace Part Soon
XXXXXXXXXX |
The product part indicated is nearing or at the
end of its service life. Contact Epson for support and provide them
with the service code shown on the LCD screen.
You must replace the part before printing again. If you continue
to print, a call for service occurs. |
| Call For Service
XXX Error XXX
Power off and then on. If this doesn't work, note the code and
call for service. |
A call for service occurs when:
- The power
cable is not connected securely
- An error
occurs that cannot be cleared
When a call for service has occurred, the printer automatically
stops printing. Turn off the printer, disconnect the power cable
from both the outlet and the printer, and then reconnect them. Turn
the printer on and off several times. If the same call for service
is displayed on the LCD screen, contact Epson for support and
provide them with the service code shown on the LCD
screen. |