Blue |
Off |
Off |
Off |
Off |
Projector is in standby mode or network monitoring and
control is in progress. |
Blue |
Flashing blue |
Varies |
Off |
Off |
Warming up. Wait for an image to appear. |
Blue |
Blue |
Varies |
Off |
Off |
Normal operation. |
Blue |
Blue |
Flashing orange fast |
Off |
Off |
Projector is connected to a 110 V power source and the
laser is operating at approximately 55% of available power.
For optimal performance, connect the projector to a
220 V power source using the 220 V power cord that came with the
projector. |
Blue |
Flashing blue |
Off |
Off |
Off |
Cooling down. All buttons are disabled. |
Flashing blue |
Off |
Off |
Off |
Off |
Preparing network monitoring. (Wait for the light to
remain orange before unplugging the projector.) |
Blue |
Blue |
Flashing blue |
Off |
Off |
The shutter feature is enabled. |
Off |
Flashing blue |
Flashing orange |
Off |
Off |
Internal error. Turn off the projector, unplug the
power cord, and contact Epson for help. |
Off |
Flashing blue |
Off |
Flashing orange |
Off |
A fan or sensor has a problem. Turn off the projector,
unplug the power cord, and contact Epson for help. |
Off |
Flashing blue |
Off |
Orange |
Off |
Projector is too hot. Wait for about five minutes so
the projector can switch to standby mode. Then check the
following:
- Make sure
that the vents and air filter are not clogged with dust or
obstructed by nearby objects.
- Clean or
replace the air filter.
- Make sure
the environmental temperature is not too hot.
- If
operating the projector at high altitude, turn on High Altitude Mode.
- If the
problem persists, unplug the projector and contact Epson for
help.
|
Off |
Flashing blue |
Orange |
Off |
Off |
Laser error.
- Make sure
that the vents and air filter are not clogged with dust or
obstructed by nearby objects.
- Clean or
replace the air filter.
- If the
problem persists, unplug the projector and contact Epson for
help.
|
Off |
Flashing blue |
Off |
Off |
Orange |
Low air flow through the projector.
- Make sure
that the vents and air filter are not clogged with dust or
obstructed by nearby objects.
- Clean or
replace the air filter.
- If the
problem persists, unplug the projector and contact Epson for
help.
|
Off |
Flashing blue |
Orange |
Orange |
Off |
No lens installed, or lens shift or supply voltage
error. Remove and reinstall the lens. If the problem persists, turn
off the projector, unplug the power cord, and contact Epson for
help |
Off |
Flashing blue |
Flashing orange |
Flashing orange |
Off |
Shutter error. Turn off the projector, unplug the
power cord, and contact Epson for help. |
Flashing blue |
Varies |
Varies |
Flashing orange |
Varies |
High temperature warning. If the temperature gets too
high, projection will automatically stop.
- Make sure
that the vents and air filter are not clogged with dust or
obstructed by nearby objects.
- Make sure the environmental temperature is not too
hot.
- Clean or
replace the air filter.
|
Varies |
Varies |
Varies |
Varies |
Flashing orange |
Clean the air filter. |
Flashing blue |
Varies |
Flashing orange |
Varies |
Varies |
Laser warning. Turn off the projector, unplug the
power cord, and contact Epson for help. |
Flashing blue |
Varies |
Flashing orange |
Varies |
Varies |
An unsupported lens is attached. Attach only a
supported lens. |
Flashing blue |
Varies |
Flashing orange |
Flashing orange |
Varies |
Shutter error. Turn off the projector, unplug the
power cord, and contact Epson for help. |
Flashing blue |
Varies |
Varies |
Varies |
Orange |
Low air flow through the air filter.
- Make sure
that the vents and air filter are not clogged with dust or
obstructed by nearby objects.
- Clean or
replace the air filter.
- If the
problem persists, unplug the projector and contact Epson for
help.
|
Varies |
Varies |
Flashing orange |
Varies |
Varies |
End of Constant
Brightness mode. |
Varies |
Off |
Flashing orange fast |
Flashing orange fast |
Varies |
When performing batch setup using a USB flash drive,
the setup file may be corrupt or the USB flash drive may not be
connected correctly. Remove the USB flash drive, turn off the
projector and unplug the power cord, then plug the power cord back
in, turn on the projector, and try again. |
Flashing blue fast |
Off |
Flashing orange fast |
Flashing orange fast |
Flashing blue fast |
When performing batch setup, an error may have
occurred when writing the settings. Turn off the projector, unplug
the power cord, and contact Epson for help. |